你在这里

Home » Resources » Protocols » Protocol for the Preparation and Fluorescent IHC Staining of Paraffin-embedded Tissue Sections

Protocol for the Preparation and Fluorescent IHC Staining of Paraffin-embedded Tissue Sections

View Graphic Protocol

The following immunohistochemistry (IHC) protocol has been developed and optimized by R&D Systems IHC/ICC laboratory for fluorescent immunohistochemistry staining experiments using paraffin-embedded tissue samples.

This IHC protocol provides a basic guide for the fixation, microtome sectioning, and staining of paraffin-embedded tissue samples. Each investigator must determine the precise experimental conditions required to generate a strong and specific immunohistochemical staining for each antigen of interest. If R&D Systems' primary antibodies are employed, please refer to the product data sheets to obtain the recommended working dilutions. In the staining protocol, signal visualization is achieved using R&D Systems' fluorescent secondary antibodies and reagents. For all other reagents, please follow the manufacturer's instructions.

Please read IHC protocol in its entirety before beginning.

Immunohistochemistry Protocol for Fixing and Sectioning Paraffin-embedded Tissues

Reagents Required

  • Formaldehyde Fixative Solution: 85 mM Na2HPO4, 75 mM KH2P04, 4% paraformaldehyde, and 14% (v/v) saturated picric acid, pH 6.9. (Picric acid is optional, enhances preservation of morphology in some tissues)
  • Ethanol: 100%, 90%, 70%
  • Wash Buffer: 1X PBS (0.145 M NaCl, 0.0027 M KCl, 0.0081 M Na2HPO4, 0.0015 M KH2PO4, pH 7.4)
  • Deionized H2O
  • Xylene (mixed isomers)
  • Paraffin

Immunohistochemistry Fixing and Sectioning Paraffin-embedded Tissue Protocol

  1. To preserve tissue morphology and retain the antigenicity of the target molecules, fix the tissue by vascular perfusion with 500 - 700 mL of Formaldehyde Fixative Solution.
    Note: When it is not possible to fix by perfusion, dissected tissue may be fixed by immersion in a 10% formalin solution for 4-8 hours at room temperature. It is commonly accepted that the volume of fixative should be 50 times greater than the size of the immersed tissue. Avoid fixing the tissue for greater than 24 hours since tissue antigens may either be masked or destroyed.
    Note: R&D Systems scientists perfuse fix all rodent tissue with the exception of lung, spleen, and embryonic tissue, which are immersion fixed.
  2. Dehydrate Tissues. Because paraffin is immiscible with water, tissue must be dehydrated before adding molten paraffin wax.
    1. Immerse the tissue in 70% ethanol three times for 30 minutes each at room temperature.
    2. Immerse the tissue in 90% ethanol two times for 30 minutes each at room temperature.
    3. Immerse the tissue in 100% ethanol three times for 30 minutes each at room temperature.
    4. Immerse the tissue in xylene (mixed isomers) three times for 20 minutes each at room temperature.
  3. Embed the tissue in paraffin at 58 °C. Tissues can be embedded into paraffin using specialized automated tissue processing systems.
  4. Cut 5 - 15 µm thick tissue sections using a rotary microtome.
  5. Float the sections in a 56 °C water bath.
  6. Mount the sections onto either ProbeOn, or ProbeOn Plus or gelatin-coated histological slides. Slides are pre-coated with gelatin to enhance adhesion of the tissue. Please refer to the Protocol for the Preparation of Gelatin-coated Slides for Histological Tissue Sections for instructions on how to prepare gelatin-coated slides.
  7. Dry the slides overnight at room temperature. Slides with paraffin-embedded sections can be stored either at room temperature or in at 2-8 °C for several years in slide storage boxes.

Immunohistochemistry Protocol for Fluorescent Staining of Paraffin-embedded Sections

Reagents Required

Immunohistochemistry Protocol

  1. Rehydrate Sections
    1. Immerse the slides in xylene (mixed isomers) 2 times for 10 minutes each.
    2. Immerse the slides in 100% ethanol 2 times for 10 minutes each.
    3. Immerse the slides in 95% ethanol for 5 minutes.
    4. Immerse the slides in 70% ethanol for 5 minutes.
    5. Immerse the slides in 50% ethanol for 5 minutes.
    6. Rinse the slides with deionized H2O.
    7. Rehydrate the slides with wash buffer for 10 minutes. Drain the excess wash buffer.
    Note: Excessive fixation may result in the masking of an epitope and strong non-specific background signal that can obscure specific labeling. If necessary, an antigen retrieval protocol can be performed at this time.
  2. Surround the tissue with a hydrophobic barrier using a barrier pen.
  3. Block non-specific staining between the primary antibodies and the tissue, by incubating in blocking buffer (1% horse serum in PBS) for 30 minutes at RT.
  4. Apply primary antibodies diluted in Incubation Buffer according to manufacturer’s instructions. For fluorescent IHC staining of paraffin-embedded tissue sections using R&D Systems primary antibodies, it is recommended to incubate overnight at 2-8 °C. This incubation regime allows for optimal specific binding of antibodies to tissue targets and reduces non-specific background staining. These variables may need to be optimized for your system.
    Note: Appropriate controls are critical for the accurate interpretation of IHC/ICC results. All IHC/ICC experiments should include a negative control using the incubation buffer with no primary antibody to identify non-specific staining of the secondary reagents. Additional controls can be employed to support the specificity of staining generated by the primary antibody. These include absorption controls, isotype controls (for monoclonal primary antibodies), and tissue type controls.
  5. Wash slides 3 times for 15 minutes each in wash buffer.
  6. Incubate with the NorthernLights™ secondary antibody diluted in Incubation Buffer according to the manufacturer’s instructions. Recommended incubation with NorthernLights™ secondary antibody is for 30 - 60 minutes at room temperature. From this step forward, samples should be protected from light.
    Note: R&D Systems NorthernLightsTM fluorescent secondary antibodies and streptavidin conjugates are bright, resistant to photobleaching and are ideal for multi-color fluorescence microscopy.
    Note: If a biotinylated antibody was used in step 4, apply the appropriate NorthernLightsTM Streptavidin conjugate in step 6.
  7. Wash slides 3 times for 15 minutes each in wash buffer.
  8. Add 300 µL of the diluted DAPI solution to each well and incubate 2-5 minutes at room temperature. DAPI binds to DNA and is a convenient nuclear counterstain. It has an absorption maximum at 358 nm and fluoresces blue at an emission maximum of 461 nm.
    Note: DAPI counterstain can obscure visualization of targets localized in cell nuclei.
  9. Rinse 1 time with PBS.
  10. Mount with an anti-fade mounting media.
  11. Visualize using a fluorescence microscope.
    Note: Initial IHC/ICC studies often require further optimization and/or additional troubleshooting steps.

Triton is a registered trademark of Dow Chemical.

Related IHC/ICC Resources

IHC/ICC Reagents

Immunohistochemistry (IHC) Protocols
Literature
Product Categories
Protocols